A Vacuum suck! Literally. There are a few things in this world that will come close to the frustration you get when your vacuum is not functioning correctly. For your vacuum to keep a good suction, regularly maintaining it is crucial. Removing debris from the dirt cup is part of the whole cleaning process. Therefore, do you want to learn how to empty a shark vacuum? Read on

When is the right time to empty a Shark Vacuum?

Most shark vacuums are accessorized with a line at the top to indicate the maximum amount of dirt that they can take before they need to be emptied. The bar is labeled as ‘Max’ or ‘Max Fill.’ However, we advise people to open their dirt cup when half full or when a little bit over the half top mark.

How to empty a Shark Navigator Vacuum Cup

Like I said above, there is no need to wait until the cup reaches the max level to open it. There is a reason why we are insisting on this. The more dirt accumulated in the cup, the lesser the vacuum’s suction power. It is very much likely mainly if you frequently use your vacuum.

If you notice strange noises or foul odors coming from the vacuum, then this is the right time to empty the cup, regardless of the level. Sometimes, the dirt cup will need to be taken out and washed together with other parts, such as the brush rolls or the filter.

Different models of shark vacuums and how to empty them

You need to understand how a vacuum operates entirely, and in the same way, you need to learn how to open a shark vacuum properly. The emptying process is quite simple. Just follow the steps below:

Step 1: Make sure you disconnect the vacuum from the power source. In case you have a cordless vac, take out the battery.

Step 2: Take out the dirt cup off the vac.

Step 3: Take the cup to a trash can.

Step 4: While holding the cup, Press the dirt release button so that the contents can fall in the trash can.

Step 5: Put the cup back into the vacuum.

It might seem pretty straightforward, but note that different shark vacuums come with different designs. You need to know how to deal with the specific vacuum you own. Every system has a unique way of operation, and you need to understand the design before learning how to empty the cup. In the following paragraphs, we will look at exactly how to drain specific models of shark vacuums.

Make sure that your vacuum is disconnected from the power source before you begin any operation. For cordless units, all you need is to turn off the power button.

Emptying the Shark Navigator LiftAway Vac

To empty this Shark version, release tabs on the dust cup need to be slid from the top of the cup to separate from the central unit. The cup should then be held over a bin to release the content inside. If you like the cup to open from the base, Press hold the release button located at the cup’s bottom.

If you are not sure if all the debris is out of the cup, repeat the process of opening the cup from the top side by Press holding the upper release tab. Then, rotate it upside down over a trash bin. After you are sure that there is nothing left, place the cup back into the vacuum.

Emptying the Shark Rotator LiftAway Vac

Just like in the first model, taker out the dust cap from the central unit. Depending on your vacuum model, you can achieve this by pulling off the release tab on the dust cup or Press holding on the go button on the cup. These buttons are near the top of the cup.

Next, when holding the cup over a dirt bin, press the tab door button on the upper side to let go of the cup’s content. At times, the cup needs to be held in an upside-down position before you press hold the release button located at the base of the cup. Before putting the cup back into the unit, make sure it is properly closed.

Emptying the SharkFLEX Vac

Take out the dirt cup off the vac. While holding the cup, Press the dirt release button so that the contents can fall in the trash can. Put the cup back into the vacuum.

This model has some wands inside the cup, and you have to be careful to make sure that you place the wands in the right position before putting the cup back into the unit. It is an essential step because these wands can affect the suction function of the vacuum.

Emptying a Shark-APEX DuoClean Vac

Like any other model discussed above, make sure that the unit is detached from the power source before you begin the operation. To get the dust cup out of the central unit, press the release wand near the top of the cup (sometimes right on top of the cup).

After taking out the cup, release the contents inside by holding it over a bin and pressing the release tab. You can also hold the cup in an upside-down position before you press hold the release button located at the cup’s base. Before putting the cup back into the unit, make sure it is properly closed!

How to empty the Shark ION, Shark ION Rocket Cordless, and the Shark IONFlex Vacs

It is a battery-operated vacuum. Press the power tab located on the handle of the unit before taking the battery off. Then take out the hand vacuum unit away from the wand by tapping on the release tab. To release the debris and dirt, look for the dust cup’s release tab and press it to remove the contents over a bin.

This unit is the simplest to operate. After you complete, place the hand vacuum back into the leading company. If you notice that the dirt cup needs to cleaning, there is a guide on cleaning this model’s dirt cup.

The final verdict on How to Empty Shark Vacuum

As we have seen in different Shark Vacuum models and empty them, the emptying process is not so hard. The only challenging or daunting part is locating the dirt cup’s release tab or removing it from the central unit. It is not hard, though, since most of these buttons are located near the top or on the dust cup.

If you are still finding it hard to locate the release tabs, read through the vac’s manual to get the directions. The emptying steps are so simple after you see the release button. All you need is to get the dust cup out of the central unit, hold it over a dust bin, and press the release tab. After you complete emptying the cup and washing it (if need bed), make sure it is dry before placing it back into the unit.

Author

Write A Comment